현대 EDS (이디에스)

H > 기술자료실 >

기술자료실

최고를 만드는 기업, HYUNDAI E.D.S

기술자료실

[UL 94] Flammability of Plastic Materials

페이지 정보

작성자 현대EDS 작성일17-03-17 16:55 조회20,115회 댓글0건

첨부파일

본문

[의견] 원자력 발전소는 대부분의 Plastic 재질의 Component에 대해서 UL 94 난연 인증을 요구하고 있다. 

계통 등급, 품질 등급에 따라서 난연 등급이 일부 상이하기는 하나, 기본적으로 UL 94 V0, V1의 자재를 선정하도록 하는 것이 가장 좋은 방법이다. 일부 Component 제조사는 영업 상 비밀을 이유로 재질 정보를 제공하지 않거나, 해당 등급에 대한 성적서를 제공하지 않는 경우가 있으므로, 자재 선정 시 유의하여야 한다. 단, UL 94 난연 요건이 아닌, Flammability 요건만 제시되는 경우에는 UL 94 HB 등급 이상으로 완화된 요건을 적용할 수 있다. 

만일, 원 제조사에서 UL 94 인증에 대한 어떤 관련 서류도 제공받을 수 없는 경우에는 ASTM D635의 요건을 적용하여, 재질이 아닌 부품에 대한 난연 시험을 수행할 수 있다. 단, 이 경우는 UL 94 HB 등급만 인증되므로, 그 이상을 요구하는 계통에서는 반드시 성적서 확보 유무를 사전에 확인하여야 한다. 

 

상세 등급과 관련된 내용 및 시험 방법에 대해서는 첨부 자료 UL-Plastic을 참조하도록 한다. 

 

Classifications

From lowest (Least flame-retardant) to highest (Most flame-retardant):

  • HB: slow burning on a horizontal specimen; burning rate < 76 mm/min for thickness < 3 mm or burning stops before 100 mm
  • V-2: burning stops within 30 seconds on a vertical specimen; drips of flaming particles are allowed.
  • V-1: burning stops within 30 seconds on a vertical specimen; drips of particles allowed as long as they are not inflamed.
  • V-0: burning stops within 10 seconds on a vertical specimen; drips of particles allowed as long as they are not inflamed.
  • 5VB: burning stops within 60 seconds on a vertical specimen; no drips allowed; plaque specimens may develop a hole.
  • 5VA: burning stops within 60 seconds on a vertical specimen; no drips allowed; plaque specimens may not develop a hole.

Foam and Films

There are other classifications that apply to low density foam materials (HF-1, HF-2, HBF) and thin films (VTM-0, VTM-1, VTM-2).

  • HF-2: burning stops within 3 seconds; afterglow less than 30s; burning drips allowed.
  • HF-1: burning stops within 2 seconds; afterglow less than 30s; no burning drips allowed.

댓글목록

등록된 댓글이 없습니다.